Thermodynamic cycle models are routinely assembled from heterogeneous sources – steam-table lookups, manufacturer data sheets, handbook correlations, and hand-computed preliminary estimates – and an error introduced in any one source (a misread enthalpy, a sign error in a heat balance, a wrong coefficient-of-performance value) can propagate silently through every downstream calculation. Engineers currently guard against this by checking governing equations pairwise, but pairwise checking has a structural blind spot: a set of equations can pass every pairwise comparison and still be globally infeasible as a system. We develop a linear-algebraic diagnostic framework that closes this gap. The governing equations of a steady-state thermodynamic cycle – energy balances over turbines, compressors, boilers, condensers, and expansion devices, together with isentropic-process relations and the coefficient-of-performance definition – form a linear system A x = b whose state vector x collects enthalpies, heat transfer rates, and work quantities at each process node. We show that global inconsistency of this system is equivalent to infeasibility of A x = b , and that infeasibility is always witnessed by a vector in the left nullspace of A that is not orthogonal to b – an algebraically certifiable condition we call a nullspace inconsistency certificate , computable from a single thin SVD and fundamentally inaccessible to pairwise checking. Building on this certificate, we prove that pairwise consistency checks are provably insufficient to detect global thermodynamic inconsistency; we establish existence and uniqueness of a minimum-norm repair vector that returns the right-hand-side data to the nearest feasible point on the constraint manifold; we derive equation-localization weights that rank which governing equation is the primary source of a fault; and we construct a differentiable repair operator whose fixed points correspond to globally self-consistent cycle models. The complete detection-localization-repair pipeline runs in O ( kn 2 ) time via a thin SVD – negligible overhead for cycle models of practical size – and requires no information beyond the equations and data an engineer already has on hand. We demonstrate the framework on the Rankine steam-power cycle and the vapor-compression refrigeration cycle, where it correctly detects, localizes, and corrects hidden inconsistencies – including a 50 kJ kg − 1 enthalpy error in Rankine cycle steam tables and a simultaneous condenser-balance fault with an erroneous COP value in the refrigeration cycle – that pass all pairwise equation checks yet render the global model infeasible. We further discuss how the certificate behaves under measurement and property-estimation uncertainty, and compare the approach against residual-based checking, data-reconciliation, and optimization-based fault detection. The framework requires only the linear (or linearized) governing equations and standard property data already used in routine cycle calculations, making it directly deployable as an auditing layer in existing engineering workflows.
Case Studies in Thermal Engineering · مجلد 75 · 107084-107084
This study focuses on waste energy recovery and environmental protection through the evaluation of an integrated clean energy system combining compressed air energy storage, a solid oxide fuel cell, and a heat recovery unit. Designed to sustainably generate power, heat, and compressed air, the system's performance is assessed from energy, exergy, and environmental perspectives. Results show that recovering waste energy by optimizing current density significantly boosts outputs, power increases from 95.46 kW to 165.8 kW, heat recovery improves from 195.6 kW to 483 kW, and compressed air generation rises from 278.8 g/s to 535.6 g/s. However, higher current density also raises electrical emissions (from 850 to 1142 kg/MWh) and cycle emissions (from 278.8 to 291.8 kg/MWh), despite a reduction in thermal emissions (from 414.9 to 392 kg/MWh), underscoring the environmental trade-offs involved. The system demonstrated energy efficiencies ranging from 60.31% to 63.85% and exergy efficiencies between 27.5% and 32.87%, depending on operating conditions. Furthermore, elevated temperatures and utilization rates negatively affect both energy and exergy efficiencies, with improved efficiencies observed at lower current densities and temperatures. These insights emphasize the importance of balancing operational parameters to maximize waste energy recovery while minimizing environmental impacts, contributing to the advancement of sustainable and efficient hybrid clean energy technologies.
waste heat recoverycompressed air energy storagesolid oxide fuel cellsheat recovery units
Case Studies in Thermal Engineering · مجلد 63 · 105267-105267
The proposed system uses a dual-loop organic Rankine cycle, a reverse osmosis desalination unit, an absorption cooling unit, and a thermoelectric generator to produce electricity and freshwater for urban areas. A thorough assessment of the system's thermodynamic and economic performance has been conducted, with a parameter-based investigation to assess the effect of key variables on the system performance. The parametric study indicates that rising the geothermal mass flow rate enhances the energy efficiency, but lowers the energy efficiency and affects the cooling requirements. Moreover, the optimum inlet temperature in turbine 1 increases the desalination efficiency up to 105.02 kg/s at 115 °C, and higher temperatures reduce the performance and system efficiency. Adjusting the temperature difference at the pinch point at Evaporator1 is crucial for system efficiency, with trade-offs between freshwater output, expenses, and exergy efficiency. The capability of the system to produce up to 6,048,000 L of potable water daily signifies a monumental leap towards meeting the water demands of nearly 42,000 individuals, based on European consumption standards. Lastly, the application of genetic algorithms in the optimization process results in an exergetic efficiency of 32.79 % and a cost rate of 58.05 $/h, demonstrating the system's enhanced operational effectiveness.
Case Studies in Thermal Engineering · مجلد 56 · 104240-104240
Marine transportation is a significant contributor to overall energy consumption among transportation sectors and is responsible for producing a considerable amount of greenhouse gases. A potential solution for alternative applications involves implementing combined heat integration, thereby enabling the production of additional utilities and mitigating emissions. The current work introduces an innovative heat integration process for a marine engine, focusing on implementing an optimal thermal matching technique to minimize overall irreversibility in producing liquefied hydrogen and coolant. The process incorporates an organic flash-bi-evaporator cooling cycle, a humidification dehumidification desalination, a polymer electrolyte membrane water electrolysis process, and a Claude cycle. The generated freshwater is delivered to the electrolyzer to produce gaseous hydrogen. This product and the cooling for freezing are utilized in the Claude cycle for hydrogen liquefaction. The study utilizes an advanced thermo-environmental multi-criteria investigation and optimization, considering sensitivity analysis and optimization based on artificial intelligence method. The optimization process incorporates the training and testing of artificial neural networks, NSGA-II method, and TOPSIS decision-making. The primary objective functions include exergetic efficiency and carbon dioxide emission. The findings demonstrate that the specified objectives are computed to be 0.121 and 2.67 kg/MWh, correspondingly. Besides, this condition exhibits a liquefied hydrogen flow rate of 6.44 L/h and a cooling output of 43.61 kW, showing an energy efficiency of 0.1145. Also, the total exergy destruction rate associated with the arranged structure is 124.5 kW. Furthermore, the optimum state reveals an exergoenvironmental index of 0.840 and an exergetic stability factor of 0.869.